Broke AXE I/O Solo, I need help.

General talk about music creation and production, or anything that doesn’t fit into the other categories

Broke AXE I/O Solo, I need help.

Postby @formantes7 » Fri Jun 02, 2023 4:46 pm

Hello everyone who can take apart their AXE I/O Solo audio interface? Help me find out if there is a part in place R192 or not? I think that part fell off when dropped, but I'm not sure.
@formantes7
 
Posts: 8
Joined: Sat Feb 18, 2023 11:21 am

Re: Broke AXE I/O Solo, I need help.

Postby Sharmon123@ » Mon Jun 05, 2023 7:37 am

R signifies resistor and if one dropped out you have a lot more problems than just replacing it.
Sharmon123@
 
Posts: 147
Joined: Sat Mar 11, 2023 11:21 pm

Re: Broke AXE I/O Solo, I need help.

Postby @formantes7 » Tue Jun 06, 2023 12:36 am

I will change the processor, and next to it is R192, but is there a resistor according to the circuit or not, I don’t know, that’s why I’m asking
@formantes7
 
Posts: 8
Joined: Sat Feb 18, 2023 11:21 am

Re: Broke AXE I/O Solo, I need help.

Postby @formantes7 » Tue Jun 06, 2023 12:42 am

please take a photo, I don’t want to burn the new processor, such processors are difficult to find in our country, you have to wait several months from China
@formantes7
 
Posts: 8
Joined: Sat Feb 18, 2023 11:21 am

Re: Broke AXE I/O Solo, I need help.

Postby Sharmon123@ » Tue Jun 06, 2023 12:49 am

That's what I am saying , R 192 is the designed 192nd resistor of that version. Whether the version in your hand requires it or not can only be seen in that version's circuit diagram. If it's part of say an RC tank that governs clock cycles then it would have to be exact and none of that +- 20% stock either. You have a daunting task ahead of you especially since it involves a rapidly emerging technology that the R&D departments are holding very close to their chests. I wish you the best of luck though. Not much YouTube help will be found on these for a couple years yet at least. It has been reverse engineered as evidenced by the counterfeits but even those scum aren't going to be publishing the designs anytime soon.
Sharmon123@
 
Posts: 147
Joined: Sat Mar 11, 2023 11:21 pm

Re: Broke AXE I/O Solo, I need help.

Postby Sharmon123@ » Tue Jun 06, 2023 12:54 am

@formantes7 wrote:please take a photo, I don’t want to burn the new processor, such processors are difficult to find in our country, you have to wait several months from China



It should say "Designed and made in Italy" actually.
Sharmon123@
 
Posts: 147
Joined: Sat Mar 11, 2023 11:21 pm

Re: Broke AXE I/O Solo, I need help.

Postby @formantes7 » Sun Jun 11, 2023 10:11 am

Sharmon123@ wrote:
@formantes7 wrote:please take a photo, I don’t want to burn the new processor, such processors are difficult to find in our country, you have to wait several months from China



It should say "Designed and made in Italy" actually.

even on the original there is no inscription that it is made in italy, the microcircuits are identical
the question was different, is the resistor soldered in place of R192?
@formantes7
 
Posts: 8
Joined: Sat Feb 18, 2023 11:21 am

Re: Broke AXE I/O Solo, I need help.

Postby @formantes7 » Thu Jun 29, 2023 1:22 pm

R192 ??!!Image
@formantes7
 
Posts: 8
Joined: Sat Feb 18, 2023 11:21 am

Re: Broke AXE I/O Solo, I need help.

Postby Sharmon123@ » Thu Jun 29, 2023 1:32 pm

The sticker on my unit ordered from IK directly says “Designed and made in Italy” that indicates to me that it was designed and made in Italy.
Sharmon123@
 
Posts: 147
Joined: Sat Mar 11, 2023 11:21 pm

Re: Broke AXE I/O Solo, I need help.

Postby @formantes7 » Thu Jun 29, 2023 2:18 pm

Sharmon123@ wrote:The sticker on my unit ordered from IK directly says “Designed and made in Italy” that indicates to me that it was designed and made in Italy.

Is it written on the microprocessor that it is from Italy, or on resistors and capacitors?
@formantes7
 
Posts: 8
Joined: Sat Feb 18, 2023 11:21 am

Re: Broke AXE I/O Solo, I need help.

Postby @formantes7 » Thu Jun 29, 2023 2:19 pm

@formantes7 wrote:
Sharmon123@ wrote:The sticker on my unit ordered from IK directly says “Designed and made in Italy” that indicates to me that it was designed and made in Italy.

Is it written on the microprocessor that it is from Italy, or on resistors and capacitors?

Did you even look at the photo?
@formantes7
 
Posts: 8
Joined: Sat Feb 18, 2023 11:21 am

Re: Broke AXE I/O Solo, I need help.

Postby Sharmon123@ » Thu Jun 29, 2023 2:44 pm

I have a device that I paid 500$ for 3 months ago that is still under warranty, I am not going to void my warranty to send you a picture of the inside of it.
Sharmon123@
 
Posts: 147
Joined: Sat Mar 11, 2023 11:21 pm

Re: Broke AXE I/O Solo, I need help.

Postby @formantes7 » Thu Jun 29, 2023 3:21 pm

Sharmon123@ wrote:I have a device that I paid 500$ for 3 months ago that is still under warranty, I am not going to void my warranty to send you a picture of the inside of it.

The question is addressed to everyone, not to you, why did you come in then ?? Decided to be smart?
@formantes7
 
Posts: 8
Joined: Sat Feb 18, 2023 11:21 am

Re: Broke AXE I/O Solo, I need help.

Postby Peter_IK » Thu Jun 29, 2023 3:25 pm

Remember that this forum is for civil user discussion. Seems we're heading away from that here, and quickly.

I'd also recommend at least asking IK Support if they have any information though accidental damage isn't typically covered under warranty they may have some insight that users here do not. It's at least worth a shot.
IK Multimedia. Musicians First.
YouTube - Facebook - Twitter
Need help? Our support team will be happy to help and can be reached at this link.
From the rules: Moderator decisions are not a matter for forum discussion and are final.
User avatar
Peter_IK
Kingpin
 
Posts: 20111
Joined: Thu Nov 18, 2010 3:40 pm
Location: Everywhere

Re: Broke AXE I/O Solo, I need help.

Postby Sharmon123@ » Thu Jun 29, 2023 3:51 pm

Besides your inappropriate racist comment my only addition is that there is not a manufacture on the planet that will send you a PCB diagram (it is likely a 3-4 layer PCB with the given real estate density. Ditto for the schematics , it’s still in active production and still being developed. They spent millions developing it , learn what you are asking for before asking it.
Sharmon123@
 
Posts: 147
Joined: Sat Mar 11, 2023 11:21 pm

Next

Return to General Discussions